Posted by Patrick Moreau on January 5, 2024 in Technology
Rod seal factory supplier by Dmsseals: What are Mechanical Seals? Mechanical seals are devices that accommodate a rotating shaft while containing and preventing the fluid from leaking out of the enclosed housing. While different mechanical seal designs are available for pumping applications, most have three sealing points. Rotating face that rotates with the shaft; Stationary face fitted to the pump housing; Interface portion between the rotating and stationary face of the seal. These three sealing points ensure that the fluid contained within the pump housing does not leak while also preventing dust particles in the atmosphere from entering the housing. The mechanical seals are usually made up of different materials to prevent sticking. Typically, one side of the seal uses softer materials like carbon graphite, and the other is made of harder materials such as silicon carbide or ceramic alumina. However, hard materials are preferred for both surfaces if the pumping application involves abrasive fluids. In addition to the two materials, the sealing unit also comes with O-rings to seal the stationary face on the housing side and the rotating face on the shaft side. Springs are also used to keep both faces pressed. In most cases, the two faces of the seals are also lubricated to prevent friction and wear. Depending on the application, this fluid film can either be a separate lubricant or the process fluid itself. Discover even more info on https://www.dmsseals.com/scraper-seals.
A basic mechanical seal contains three sealing points. The stationary part of the seal is fitted to the pump housing with a static seal –this may be sealed with an o-ring or gasket clamped between the stationary part and the pump housing. Rotating and Stationary parts of a Seal – The rotary portion of the seal is sealed onto the shaft usually with an O ring. This sealing point can also be regarded as static as this part of the seal rotates with the shaft. The mechanical seal itself is the interface between the static and rotary portions of the seal. One part of the seal, either to static or rotary portion, is always resiliently mounted and spring loaded to accommodate any small shaft deflections, shaft movement due to bearing tolerances and out-of-perpendicular alignment due to manufacturing tolerances.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.
Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.
The guide belt is a belt-shaped member that guides the moving parts. Its main function is to guide. In order to realize the function of guidance, it must support the guided member, and guide and correct its motion trajectory. In order to realize the guiding function well, it also requires isolation, shock absorption and noise reduction of the guiding parts. Guide belts are mainly used in oil cylinders and cylinders. Due to their excellent performance, they are also widely used in other motion mechanisms. Read more details at https://www.dmsseals.com/.
DMS Seals is a professional hydraulic seals, industrial mechanical seals manufacturer and oil seal supplier specializing in supplying sealing solutions and various seals & o ring. As a leading custom o ring manufacturer, DMS can support OEM and ODM and can meet customers’ requests. DMS Seals adheres to the tenet of “first-class design, top manufacturing, excellent service” and strive to be an excellent supplier of sealing system solutions. DMS Seals pays the utmost attention to quality to ensure the satisfaction of our cooperative partners.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
The bearing seal maintains lubrication where needed and helps protect the working part from abrasive particles and corrosive moisture. The seals are precisely configured to provide extremely low friction and excellent contamination resistance. It is perfect for high speed or low torque equipment as well as dusty environments. Moreover, the seal is reasonably designed to provide superior resistance to foreign particles.