Posted by Marie Poppins on January 2, 2024 in Manufacturing
Spring seals factory in China: A basic mechanical seal contains three sealing points. The stationary part of the seal is fitted to the pump housing with a static seal –this may be sealed with an o-ring or gasket clamped between the stationary part and the pump housing. Rotating and Stationary parts of a Seal – The rotary portion of the seal is sealed onto the shaft usually with an O ring. This sealing point can also be regarded as static as this part of the seal rotates with the shaft. The mechanical seal itself is the interface between the static and rotary portions of the seal. One part of the seal, either to static or rotary portion, is always resiliently mounted and spring loaded to accommodate any small shaft deflections, shaft movement due to bearing tolerances and out-of-perpendicular alignment due to manufacturing tolerances. Read additional details at hydraulic seal suppliers.
Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications.
Due to the volume and weight limitations of the system, it is impossible to install an ideal filtration and cooling system. High temperature, high pressure, and high speed cause the hydraulic oil to deteriorate easily, and the mechanical parts are also prone to erosion and stains. There are many stains and impurities in hydraulic oil, but it cannot be thoroughly filtered, which is the aspect of endogenous stains. All kinds of dust in the working environment may be very large, and it will inevitably enter the hydraulic system in multiple ways, causing oil pollution, which is an external stain. Therefore, the sealing system is required to be resistant to stains.
The O-ring of DMS SEALS is often used in hydraulic and pneumatic transmission systems and has wide applications. It can be used for both static and reciprocating seals. Moreover, it can also be used in rotary sealing systems. The O-ring can be installed in a groove with a rectangular cross section on the outer or inner circle, achieving a good sealing effect. It has many advantages compared with other types of sealing rings. Its compact structure makes it easy to assemble and disassemble. Moreover, its dynamic frictional resistance is relatively small, and a single piece of O-ring can achieve sealing performance in both directions.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
DMS Seals piston seals can be used very effectively in the clearance between the two chambers of the hydraulic cylinder and cylinder. The piston seal is pushed by the pressure of the fluid. Its good working performance can improve the efficiency of the machine. Due to its excellent resistance to leakage, it helps the machine to extend the machine’s working life. Our seals provide the best tight adhesion for the sealing system with low internal leakage and frictional resistance.
Diffusion leakage: Driven by the concentration difference, the medium leaks through the material transfer generated by the sealing gap or the capillary of the sealing material. Diffusion is the result of molecular motion and is not unidirectional. When the sealing pressure difference is extremely small or in a vacuum state, or when sealing permeable substances such as nitrogen and hydrogen, as well as highly toxic and radioactive substances, special attention should be paid to the leakage and diffusion.
The guide belt is a belt-shaped member that guides the moving parts. Its main function is to guide. In order to realize the function of guidance, it must support the guided member, and guide and correct its motion trajectory. In order to realize the guiding function well, it also requires isolation, shock absorption and noise reduction of the guiding parts. Guide belts are mainly used in oil cylinders and cylinders. Due to their excellent performance, they are also widely used in other motion mechanisms. Read additional information at https://www.dmsseals.com/.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.