Posted by John Concrane on March 27, 2020 in Automotive
Several tricks for paintless dent repair needs: The two techniques mentioned above will remove the majority of hail damage on your car, but a professional job at your local auto body shop is recommended for deep dents or badly damaged surfaces. The services tend to be cheap, fast and rarely require a new paint job. However, it is a good idea to compare prices and offered services at various body shops to see which package works best for your wallet and car’s situation.
1st let’s start with some car paint care tips: If you can not expose your car to the sunlight, you can use a hair dryer instead. Just aim the hair dryer to the areas you want to fix, and wait until the dents even out. The ideal distance between the hair dryer and the car should be 2-4 inches. While using a hair dryer, there should be an interval of 2 minutes. If the car’s paint starts discoloring, you should stop applying heat right away. Use a rubbing compound or wax to revise the paint color.
Decontamination: Life is a jungle out there and the air is filled with unseen pollutants. Never mind the fact that you are breathing these pollutants into your lungs, but the endless particles of pollution is in fact harmful to your car paint. Nest time you have your car washed, glide your hand across the surface of your new car paint ans see if you don’t feel a surface that is less than silky smooth. Most likely you your hand will feel what feels like small particles stuck to the paint that will give it a certain unwanted texture.
Instead, save yourself some of that hard-earned money and do it yourself. There are plenty of ways to get a small dent or ding out of a vehicle at home without ruining your paint, and you don’t need to be a gearhead to do it. However, not all of these tricks will work on your particular automobile; your mileage may vary depending on where the dent is and what your body panel, hood, or bumper is made of (aluminum, carbon fiber, plastic, fiberglass, steel, etc.). For instance, aluminum has little memory properties, so paintless dent removal is much more difficult.
Using the Right Wax. Since each type of paint reacts differently to wax and polish, you need to find out which paint was used on your car and purchase detailing products that suit the paint. Some products may act as abrasive agents and strip the car off its original shine. Discover even more details at Auto Decals & Lettering Colorado Springs.
The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.