Posted by Patrick Moreau on May 6, 2024 in Industrial
Welding curtains shopping UK in 2024: The strength of a joint can be imperative or a non-factor, depending on the purpose of the welding process. Arc welding joints are generally extremely strong unless they are not performed properly. The resulting strength of the material is often at least as strong as the base materials and, in many cases, actually stronger. Brazing joints are not structural in general, but they can bear some load. In plumbing, for example, water hammering can be an issue in some systems, so the joints need to be able to stand up to that kind of force. They are not structural, however, so there is a maximum load they can bear. Soldering joints are almost never structural in any way, and the forces they handle are more electrical than tensile, linear, or shear. As such, they are not very strong, but they don’t need to be. There should, ideally, be next to no force put on them. See more details at Fume Extractors online store UK.
Note that some of the less expensive auto-darkening shades don’t adapt to the level of brightness of an arc. Called fixed-darkening shades, these simply darken to a specified level, which may or may not be enough, just like a fixed-darkness shade. Generally, if you’re going for an adaptive shade, you want one with full adaptivity. Bear in mind, too, that many auto-darkening systems can wear out over time, and they require a power source, so you need to replace or recharge batteries or make sure any solar integration is clean and functional. It’s an additional potential area of failure that can prematurely end the life of an otherwise good helmet. Every welding operator needs some kind of protection. It’s just a matter of what kind of protection works best for you. It will take some evaluation and shopping to find that ideal helmet, but with thousands of options out there across every possible iteration of the factors listed above, there’s guaranteed to be something for you. You just need to find it.
Certified training programs teach welders the best practices in safety and welding techniques, significantly reducing the risk of accidents due to operator error. Certification also often includes up-to-date education on the latest safety standards and technology in the welding industry. Many welding processes involve gases that can be hazardous if not handled correctly. Safe storage, handling, and usage practices must be strictly followed to prevent leaks, explosions, and health hazards. Proper procedures in managing gases and chemicals prevent dangerous exposures and ensure that the work environment remains safe for all personnel. This includes having appropriate gas detectors and ventilation systems in place.
The sort of build quality that you’d expect from Makita. This angle grinder is tough, well put together and built to take a beating. Makita have included a lock-off power switch. I’m a big fan of these compared to the “deadman” style switch you need to hold to keep the disc spinning. They can tire your hand out quickly and aren’t ideal for long grinding sessions. You get a 2.5m power cable to play with. It’s long enough for most grinding jobs, and the quality of the power cord is excellent as well. Makita use labyrinth rings to seal the bearings against dust. Anyone who uses angle grinders a lot know how much dust they produce, so this is a welcome feature. Attaching the side handle can be a bit of a pain. You’ll need a long screwdriver to hold the bolt in place inside the handle. Compared to simple screw-in handle on the Bosch GWS 7-115, this one can be tricky.
UK market choice: LOTOS Technology is a California company that has only been around since 2007. Still, the LOTOS MIG is impactful and high quality enough to make it onto our list. This one is a versatile machine that is a fair price of about $400. And—provided that you have the necessary 240-volt outlet in your home—it can be set up in a matter of minutes. The duty cycle of this welding newcomer is impressive, and it can be utilized by pros and amateurs who have been continually impressed by the bang they’ve gotten for their buck. The LOTOS can weld steel and stainless steel from 18 gauge to ¼ inches and aluminum to 1/8 inch or thicker. Thermal overload protection doesn’t let this machine overheat, and infinitely adjustable heat/amperage as well as wire speed makes using the LOTOS simple. Check out the LOTOS MIG140 for a lower power alternative.
Once you know how you’re going to be using your MIG welder, you’ll also need to think about what kind of weld you’re going to be doing. Consider the output of the machine that’s right for the kind of materials that you’ll be working with. The thicker the metal you work with, the more power you’re going to need in your MIG welder. Additionally, if a welder needs to use more than 100 volts, it will probably need a power supply. Ultimately, one of the main concerns that you’ll need to think about when choosing the right welder is how you’re going to make sure that your machine is safe and practical. There’s more to think about with a MIG welder than how you want the weld to look after you’re finished with it. However, if you’re looking for a clean finish, bear in mind that a Pulse MIG welder can reduce the risk of burning through your chosen metals. See more details on weldingsuppliesdirect.co.uk.
Resistance or pressure welding uses the application of pressure and current between two metal surfaces to create fusion. Workpieces are placed in contact together at high pressure with a current passing through the contact point. The resistance in the metals generates heat which fuses together the metal surfaces of the workpiece. Resistance spot welding (RSW) uses two electrodes to press together overlapping metals while a welding current is applied through the resistive metals. Heat is generated and the metal surfaces fuse together to create a weld joint in the shape of a button or nugget. Metals are fused using large amounts of energy in a short time span (approx. 10-100 milliseconds) joining the workpieces almost instantaneously. The area around the weld nugget stays unharmed by the excessive heat, thus the heat-affected zone is minimal with spot welding.
Industrial gas cylinders have been around for a long time. They are widely used for welding, medical applications, fermenting liquids, and several other applications across various industries. In addition to these, new applications for these cylinders are emerging, as new industries and technologies are evolving. These cylinders are filled with low molecular weight chemicals in a gaseous form. Acetylene, oxygen, nitrogen, carbon dioxide, hydrogen, argon, and helium are some gases, which are used regularly. These chemical gases have distinct properties, which are exploited in various industrial applications. If not handled properly, these industrial gas cylinders may be hazardous in various industrial conditions. This post shares some important safety tips for handling industrial gas cylinders in an industrial facility.
Do you feel frustrated because the disc grinder work is not progressing well, or you are running out of time? If that is your problem, then this Metal Cutting Disc will help you. It is a high-quality product that has been designed to provide ultimate performance. The wheels are made of steel and have a tooth count of 25. They are great for concrete, metal, or other materials where you want to cut through tough materials quickly. These discs are made from high-quality cutting wheels with a flat shape. They have a 3? diameter and a 1/16? thickness. With ultra-thin metal and stainless steel, they can quickly and easily cut through burrs and other unwanted materials. With these discs, you can grind metal and stainless steel fast and smooth while minimizing noise. As a versatile option for workshops, the discs can be used with sheet metal, die grinders, air cut off tools, and electric cut off tools.
The duty cycle is the amount of time the welder can run continuously before needing to cool down. It’s expressed as the percentage of 10 minutes the MIG welder can run. So a 20 percent duty cycle at 90 amps would mean that when you’re welding at a 90 amp rating, you can go continuously for 2 minutes before the welder needs to cool off for 8 minutes. That means if your 140-amp welder is rated for 20 percent at 90 amps, it’s probably only able to weld for less than a minute at the full 140 amps. How Much Power Do You Need? This is the single factor that affects the cost of MIG welders. Newer 120 volt machines are able to run up to 140 amps, good enough for ?-inch steel. However, at that rating, the duty cycle will be fairly short. That’s not a big concern for home hobbyists and weekend warriors, but it will really put a cramp in your style if you’re doing production welding. Dual-voltage machines are now beginning to provide a lot of control, at least on the 240 side, but unless you’re buying big-name stuff that can get pricey, it’s likely the 120 side won’t provide the same quality of welds.
In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.
How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).
A few tips on welding equipment, MIG and TIG welders, plasma cutters. Welders with a higher power output can work with thicker metals, but higher voltage welders will require special power supply set ups—either generators or appropriate power outlets. A welder with lower voltage in the 100’s will not be able to handle heavy duty jobs, but it can be plugged in and operated from any outlet. Any welder with power over 200 cannot run off a typical power outlet and will naturally cost more to run. In addition, welders will either run an alternating current (AC) that reverses itself at regular intervals or a direct current (DC) that flows in one direction and does not reverse itself. DC offers a steady rate of energy that leads to hotter temperatures and deeper weld penetration. AC welders usually cost less than DC welders, but the available electrodes are far more limited for AC. In fact, DC welders are more costly but remain popular because their higher power offers a wider selection of electrodes and a number of working advantages such as: simple arc striking, better penetration, and improved control. Welders who expect to work on a wide variety of projects may want to consider an AC/DC combination welder.
The X-Tractor from Lincoln has a “Mini” in it, which is self-explanatory. The machine isn’t as heavy-duty as most welding fume extractors, but no other device can beat the X-Tractor Mini in terms of portability. The X-Tractor Mini is compact and extremely lightweight. You can just pick it up and set it anywhere you like, from your garage to a store. But, the lighter weight doesn’t compromise efficiency. 2 Different Airflow Settings and 2.4 HP Motor This portable weld fume extractor comes with 2 different settings to choose the preferred airflow. The lower one will generate 95 cubic feet per minute, and the higher one will generate 108 cubic feet of airflow per minute. The amount of airflow seemed a little less to me, but you can’t expect more from a 2.4 HP motor. Besides, the size of the machine speaks for itself that it’s highly portable, which requires a bit of compromising on the power’s end.
Although this is a regular drill press and not a magnetic drill press, you can also use this one for steel drilling. The motor has a rating of ½ HP and in order to change the drill speed for metal drilling, you have to change the belt and pulley combination setting to the slowest speed. As a drill press, the RIKON 30-120 does not have the best performance. The feeding wheel is not well made and is awkwardly situated. Your chances of getting the back of your fingers caught between the feeding wheel and the belt tensioner are quite high and it is very painful. The packaging of this drill press is poor as well. If you are looking for a tool that you can use for drilling steel exclusively, we recommend that you stick to magnetic drill presses. Regular drill presses can work great for wood, plastics, and steel, but they don’t have magnets and is impossible to use for vertical and overhead applications.
ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.
GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.
If you’re a beginner welder but don’t mind splashing the cash for a top of the range welder, then try the Millermatic 141. Miller have really pushed the boundaries of usability with this welder and it features an auto-set feature for an easy set up, and infinite voltage and wire speed control. All you have to do is select the thickness of the metal you’re welding and you’re ready to start welding straight away. If you open up the machine you can tell that all the parts are great quality and really durable as well. There are more powerful welders on the market for the price, but there’s nothing better for welding up to 3/16 inch steel. See the full review here.
MIG welders are divided into transformer and inverter models. Briefly, transformer machines feature only mechanical parts that can adjust the output voltage “sequentially” while the unit is off. The output voltage is not stabilised and may decrease under load. Still, a simple design is the main benefit of transformer welders that facilitate their maintenance. Also, they are often cheaper. Inverter MIG welders are fitted with electronics that allow a smooth voltage adjustment, so it isn’t susceptible to drops and does not fall under load. Of course, power is the main feature of any electric tool. As for MIG welders, their power depends on the maximum amperage, more usually, the output range. This range determines the unit’s field of application. Powerful models can be used on small construction sites or in repair shops, while less powerful models are usually used for private needs. For example, the welders of up to 200A are great for home use; the 300A models are suitable for small repair shops, and if you need a high output and continuous work, consider welders over 300A.