Posted by Marian Vasilescu on October 21, 2023 in Manufacturing
Top 2 sided planer manufacturer: The most common application involves gluing a coating (veneer, laminate, composite, PVC etc) onto a substratum (MDF, hardboard, plywood, hollow panels, blockwood etc). The basic configuration of the pressing line is comprised of a feed belt, an automatic press and a discharge deck. This configuration can be completed with numerous options, such as glue spreaders, polishers, automatic feeders, disk, roller or belt conveyors, automatic assembling stations, panel turners and stackers. Lines with various degrees of automation can be supplied right up to fully automatic lines that do not require direct intervention by the operator. See more info at https://www.v-holdmachinery.com/double-side-planner.
The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.
A typical hydraulic down-acting press uses a pair of hydraulic cylinders, one on each end, to generate the tonnage required for the down stroke of the machine. Traditionally, these machines have a C or O frame profile design. With both types, when facing the front of the machine the hydraulic cylinders are located on the left and right hand side of the upper beam. Since the upper beam is being pushed down and up with hydraulic power, the upper beam will fall during a power outage and could create an unsafe environment. Down acting presses are commonly blocked at night to take pressure off of the hydraulic system. The lower beam does not move during bending so the operator will not get feedback that the brake is engaged.
Sanding is the operation of finishing wooden items after they have been machined. Essentially, a sanding machine performs a sand papering job to produce a uniformly sanded surface. Three common types of sanding machines are : Belt sander; Spindle sander; Disc sander. It has an endless cloth backed abrasive belt which runs over two drums and is used for sanding and shaping flat surfaces. One of the drums is rotated by an electric motor and serves as the driver, while the other supports the belt and keeps it in proper tension. For sanding work by the abrasive belt, the the workpiece is supported by an adjustable table that may be tilted to any desired angle.
The woodworking lathe is one of the most important machines used in a carpentry shop. This is employed primarily for turning jobs in making cylindrical parts. However, by suitably manipulating the tools, tapers, radii, and other irregular shapes can also be easily turned. It resembles the engine lathe most frequently used in the machine shop, and consists of a cast iron bed, a head stock, tail stock, tool rest, live and dead centers, and a speed control device (Fig. 10.54). The drive, in modern lathes, is individual motor driven ; and a cone pully on the head stock spindle is connected by a belt to a cone pully on the motor shaft.
Modern machinery often requires pneumatic pressure, be it for saws, sanders, impact wrenches, grinders, spray guns, washers, stapling, nailing or pneumatic tooling, the compressor has become a necessity. The compressor consists of: motorised pump; tank for storing the compressed air; on/off control; regulator. There’s also a metal frame on which all the parts are mounted, usually with a carrying handle and occasionally wheels. A drill press can be used to drill round holes, sanding, grooving and mortising with the addition of specialised attachments. Read additional information on v-holdmachinery.com.
The woodworking machines are the machine designed to work with wood. These machines, which are typically powered by electric motors, are widely used in woodworking. Grinding machines (used for grinding down to smaller pieces) are sometimes included in the definition of woodworking machinery. Modern carpentry shop, in addition to the hand tools described earlier, requires the use of some power-driven machines, particularly where largescale production is to be obtained. The size and capacity of the machines used depend on the size of the general run of the work to be done. Machines chosen for carpentry shop must be well built, and their accuracy should be dependable. They should be well guarded to protect the worker from the hazards of operation.